Blade Nano QX FPV BNF Manuel d'instructions

RTFREADY-TO-FLY®

10ENRTFTransmitter ControlFGHEADCBDual rate selectionHA B CDEFG HMode 1 Power LED/fl ight mode indicatorAileron (Left/Right) Throttle (Up/Down)Throttle

11ENRTFFlight Mode and Rate Selection – RTFThe nano QX RTF model comes with the Blade® MLP4DSM transmit-ter. This transmitter’s fl ight mode selection

12ENLED CodesTransmitter Setup TableEquipment LED Color LED Status OperationQuadcopterBlueRapid Blink Bind ModeSlow Blink No Link To TransmitterSolid

13ENElevatorForwardElevator downElevator upBackwardRudderRudder leftRudder rightUnderstanding the Primary Flight ControlsThrottleThrottle downThrottle

14ENAileronAileron leftLeftAileron rightRightRear ViewRear View4-in-1 Control Unit FunctionThe unique Control Unit installed in your nano QX is a ligh

15ENLED IndicationsSolid Red: ChargingSolid Green: Max ChargeCAUTION: Only use a charger specifi cally designed to charge a Li-Po battery. Failure to d

16ENDisplay Adjustment• Press Left or Right on the Display Button to adjust the video contrast in the headset.• Press Forward or Back on the Display B

17EN• After confi rming the rotor blades rotate in the correct direction, test the motor response controls.• Adjust the throttle to a low level of powe

18ENTIP: These are all possible with the RTF transmitter. When using a computer transmitter, however, increase the travel beyond 100% on aileron, elev

19ENCaring for the Video Transmitter AntennaIf your video transmitter antenna gets bent or fl attened as a consequence of a hard landing, bend the ante

2ENWARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product co

20EN182410 101199127635Exploded View

21ENParts ListingsPart # DescriptionBLH7200 FPV nano QX RTFBLH7280 FPV nano QX BNF W/O Goggles1BLH7201 Blue Canopy: FPV nano QX2BLH7202 Prop CCW Blue

22ENTroubleshooting GuideProblem Possible Cause SolutionNano QX control response is inconsistent or requires extra trim to neutralize movementAircraft

23EN Problem Possible Cause SolutionLED on receiver fl ashes rapidly and aircraft will not respond to transmitter (during binding)Transmitter too near

24ENLimited WarrantyWhat this Warranty CoversHorizon Hobby, LLC, (Horizon) warrants to the original purchas-er that the product purchased (the "P

25ENdamaged parcels, as Horizon is not responsible for merchan-dise until it arrives and is accepted at our facility. An Online Service Request is ava

26ENFCC InformationThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not c

27EN(in accordance with ISO/IEC 17050-1)No. HH2014100203Product(s): Nano QX FPV BNF without GogglesItem Number(s): BLH7280Equipment class: 1The o

28ENInstructions for disposal of WEEE by users in the European UnionThis product must not be disposed of with other waste. Instead, it is the user’s r

112IT©2014 Horizon Hobby, LLC.Blade, E-fl ite, SAFE, the SAFE logo, DSM, DSM2, DSMX, Bind-N-Fly, the BNF logo, Celectra, ModelMatchand the Horizon Hobb

3EN• Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject

4ENLi-Po BATTERY PACK7.4V 760mAhBox Contents• Blade® FPV nano QX• 150mAh 1S 3.7V 45C Li-Po Battery• 1S USB Li-Po Charger, 350 mAh• MLP4DSM• 4 AA Bat

5ENTable of ContentsFirst Flight Preparation ... 6Flying Checklist ...

6ENFirst Flight Preparation• Remove and inspect contents• Begin charging the fl ight battery• Install the fl ight battery in the quadcopter (once it ha

7ENLow Voltage Cuto (LVC)When a Li-Po battery is discharged below 3V, the battery may become damaged and may no longer accept a charge. The nano QX

8EN1. Lower the throttle and throttle trim to the lowest settings.2. Power on the transmitter.3. Install the battery by sliding it into the battery m

9ENTransmitter and Receiver BindingGeneral Binding Procedure1. Disconnect the fl ight battery from the quadcopter.2. Refer to the Transmitter Setup Tab